An LS engine code alone may point to more than one cam bearing set. Use the table to compare cam journal diameter, housing bore and bearing width, then find the relevant part number in the store links below.
Cam bearing dimensions and part numbers
Engines and blocks covered
LS1, LS2, LS3, LS6, LS7, LS9, LQ4, LQ9, LM7, LR4, L76 and L98.
The guide also covers GM LSX, Dart, RHS and Warhawk blocks, along with
Gen V engines including the LT1, LT4, L83, L86 and L8T.
Click or tap a part number to copy it.
| Engine / block | Cam journal Ø (in) | Housing bore Ø (in) | M77 / Clevite | Dura-Bond / ACL / other | Application notes |
|---|---|---|---|---|---|
| LS1 / LS2 Gen III, 1st design |
2.1650–2.1670″Width 0.880″ | 2.3260–2.3280″Width 0.880″ | SH-1814S | CHP-10, 5C1000S-00 | Early Gen III blocks with the first-design cam tunnel. |
| LS2 / LS3 / LS6 Gen III–IV, 2nd design |
2.1650–2.1670″Width 0.900″ | 2.3460–2.3480″Width 0.900″ | SH-2125S | CHP-25 / CHP-25T, 5C1001S-00, Sealed Power 1923M | This size appears in several Gen III and Gen IV applications. Check the block’s cam tunnel design. |
| LS7 / LS9 Late LS applications |
2.1650–2.1670″Width 0.950″ | 2.3460–2.3480″Width 0.950″ | SH-2157S | CHP-25 / CHP-25T | The listed housing bore matches the LS3 row. Check bearing width and oil hole layout for your block. |
| LSX / aftermarket Big-bore and 55 mm cam applications |
2.1820–2.1825″Width 0.950″ | 2.3550–2.3760″Width 0.950″ | SH-2142S | GMP-9 / GMP-10 / GMP-25, Dart 32210101 (single), Dart 32210101-5 (set of 5), STRGM-55-T1 | For GM LSX, Dart, RHS and Warhawk blocks, use the block manufacturer’s cam tunnel specification. Check whether the part number is for one bearing or a full set. |
| Gen V / LT LT1, LT4, L83, L86 |
2.1650–2.1670″Width 0.900″ | 2.3460–2.3480″Width 0.900″ | — | CHP-26T | LT-specific bearing set. The listed bore range matches the second-design LS row. Check the oil hole layout and coating in the product specifications. |
| RHS LS Race Block Single replacement bearing |
— | — | — | RHS 549202-1 (single) | Replacement bearing for the RHS aluminum LS race block. Sold individually. Five bearings are required per engine. |
Shop LS and LT cam bearings
- Dura-Bond - CHP-25 - Dura-Bond - Bond - Chp-25 - Hp Cam Bearing Set - Gm Ls 08-10
- Dura-Bond - CHP-10 - Dura-Bond - Bond - Chp-10 - Hp Cam Bearing Set - Gm Ls 1
- Sealed Power - 1888M - Camshaft Bearing - Standard Journal - Gm Ls-Series
- Dura-Bond - CH-10 - Dura-Bond - Bond - Ch-10 - Cam Bearing Set - Gm Ls 1 / Ls 6 / Vortec
- RHS - 549202-1 - Cam Bearing - Ls Block (1Pc)
- ACL Bearings - 5C1000S-00 - Camshaft Bearing - Standard Journal - Gm Ls-Series
- ACL Bearings - 5C1001S-00 - Camshaft Bearing - Standard Journal - Gm Ls-Series
- Clevite M77 - SH1814S - Camshaft Bearing - Standard Journal - Gm Ls-Series - Kit
- Clevite M77 - SH2125S - Camshaft Bearing - Standard Journal - Gm Ls-Series - Kit
- Clevite M77 - SH2142S - Camshaft Bearing - Standard Journal - Gm Ls-Series - Kit
- Clevite M77 - SH2157S - Camshaft Bearing - Standard Journal - Gm Ls-Series - Kit
- Dart - 32210101 - Coated Cam Bearing (1) - Sbc 55Mm Babbit
- Dart - 32210101-5 - Cam Bearing Set - Coated Sbc W/55Mm Dia.
- Dura-Bond - CH-25 - Dura-Bond - Bond - Ch-25 - Cam Bearing Set - Gm Ls 08-10
- Dura-Bond - CHP-10T - Dura-Bond - Bond - Chp-10T - Hp Cam Bearing Set - Gm Ls 1 Coated
- Dura-Bond - CHP-25R1 - Dura-Bond - Bond - Chp-25R 1 - Cam Bearing Set Gm Ls W/.010 Oversized Od
- Dura-Bond - CHP-25T - Dura-Bond - Bond - Chp-25T - Hp Cam Bearing Set - Gm Ls 08-10 Coated
- Dura-Bond - GMP-10T - Dura-Bond - Bond - Gmp-10T - Cam Bearing Set - Dart Ls Next Block Coated
- Dura-Bond - GMP-25 - Dura-Bond - Bond - GMP-25 - Hp Cam Bearing Set - Gm Lsx Blocks
- Dura-Bond - GMP-25T - Dura-Bond - Bond - Gmp-25T - Hp Cam Bearing Set - Gm Lsx Blocks Coated
- Dura-Bond - GMP-9 - Dura-Bond - Bond - GMP-9 - Hp Cam Bearing Set - Rhs Ls Block
- Dura-Bond - GMP-9T - Dura-Bond - Bond - Gmp-9T - Hp Cam Bearing Set - Rhs Ls Block - Coated
- King Bearings - CS5172HPT - Camshaft Bearing - HP Series - Standard Journal - GM LS-Series
- Sealed Power - 1923M - Camshaft Bearing - Standard Journal - Gm Ls-Series
- Straub Technologies - STRGM-55-T1 - Straub Technologies 55Mm Babbit Cam Bearing Set -Coated W/1 Hole
- Dura-Bond - CHP-26T - Dura-Bond - Bond - Chp-26T - Cam Bearing Set Gm Genv Lt 1/Lt 4 Coated
What do Cam Saver and Block Saver mean?
Cam Saver
Match the bearing I.D. to the cam journal. An undersize I.D. is intended for a camshaft whose journals have been ground undersize. A listing marked .010″ under I.D., for example, refers to the change from the standard diameter.
Measure the finished journals before selecting an undersize. Check the available sizes for the specific bearing series.
Block Saver
Match the bearing O.D. to the housing bore. An oversize O.D. is intended for an enlarged cam bearing housing bore. Markings such as +.010″ and +.020″ describe the increase over the standard outside diameter.
Dura-Bond references include CHP-10R, CHP-25R1 and CHP-25R2. Check the required housing bore at each bearing position.
Installation tips
- Measure the cam journals and each housing bore. Compare your measurements with the specifications for the bearing set.
- Confirm the bearing position and oil hole alignment before driving each bearing into place. Pay particular attention to the oil passages on LS7 blocks.
- For a 55 mm cam application, check both the camshaft journal specification and the block manufacturer’s housing bore dimensions.
- Check running clearance using the installed bearing I.D. and the measured journal diameter. Use the clearance specified for your application.
- Cam bearing installation tool: Comp Cams - 5312 - Cam Bearing Installation Kit
Bearing material and coating
For a high-performance build, check the bearing manufacturer’s
recommendation for your block, camshaft and intended use.
Use this table to compare dimensions and identify part numbers. Production changes and block machining can affect bearing selection. If a measurement falls outside the manufacturer’s specification, resolve the difference before installation. The engine builder is responsible for final bearing selection and installed clearance.
